MSR *WILL* be finished, come hell or high water... hell more likely.

[nodtveidt]

(and the bitches)

QFT.

[touko]

its all for the glory (and the bitches)

Lol, i like that, mainly for bitches ..

However, i see no glory in spoiling 400 useless copies for pigeons shooting, or coasters .  

[meka]

Is this for sale yet, the paypal link still stipulates that it is still on preorder.

[nodtveidt]

Until the boxes arrive in Illinois in a week or so, it's still considered a preorder. We haven't had any updates from Nationwide since the authorization... no news is good news, I suppose.

[lord_cack]

its all for the glory (and the bitches)

Lol, i like that, mainly for bitches ..

However, i see no glory in spoiling 400 useless copies for pigeons shooting, or coasters .  

Hey, they are top shelf coasters though, and probably cheaper than the equivalent in Clay Pigeons, though its been years so I don't know the going rate for them these days hehe

[touko]

lol .
which is expensive in clay pigeons,  it is the wings .

[nodtveidt]

We heard from Nationwide... they're confused. lol. They stated that there was an issue at 1:17 in the disc, causing "a loud buzz". Of course, 1:17 is where track 2 starts, which is the data track... Keranu had to tell them "hey bozos, this is a Turbob game, so you better obey". Hopefully this doesn't delay anything.

[Black Tiger]

They also pointed out that the spine was upside down on one side.

I'd say that hearing from them this far along without any problems about the disc copying properly is a very good sign.

[Arkhan]

I'd say that hearing from them this far along without any problems about the disc copying properly is a very good sign.

But, they haven't copied the disc yet.

This is them still verifying the pretend one.  They aren't going to create a glass master until they are 100% sure this thing is legit and good to go.

[nodtveidt]

They also pointed out that the spine was upside down on one side.

I'm pretty sure Keranu told them that that's how it's supposed to be.

[Black Tiger]

I'd say that hearing from them this far along without any problems about the disc copying properly is a very good sign.

But, they haven't copied the disc yet.

This is them still verifying the pretend one.  They aren't going to create a glass master until they are 100% sure this thing is legit and good to go.

So it takes them a week or two to verify a disc before attempting to copy it? Did they send you a message once they determined it was all good?

[Arkhan]

So it takes them a week or two to verify a disc before attempting to copy it? Did they send you a message once they determined it was all good?

They do more in that week than just verify the disc, and any time you have to respond before they can proceed adds to the time taken. 

I sent in the master disc, they verified it and asked if my art looked ok (sent proofs), I said yes do it, and then we were all set.

It took 1.5 weeks from the time I overnighted the discs to the time they showed up at my house.

My first master I sent was slightly gooned up so they said to send a new one, so I ended up overnighting ~10 of them or something and said here pick the best one.

[GohanX]

The fact that they are paying such close attention is a very good sign! I guess I should get off my lazy ass and preorder...

[Arkhan]

The fact that they are paying such close attention is a very good sign! I guess I should get off my lazy ass and preorder...

well they have to.  that's how it works lol.

otherwise they make a defective disc, and piss everyone off, and have to fix it. 

and that would be a waste of money and resources for the company.

[Keranu]

They also pointed out that the spine was upside down on one side.

I'm pretty sure Keranu told them that that's how it's supposed to be.

Sure did!

Waiting for our project manager to get back to us with more info.