My latest little project (new CD-rom case latches)

[TheClash603]

I need one of these for sure.  Depending on price, I'd buy two because a spare never hurts.

[HailingTheThings]

The only problem with using Shapeways for the case is that they are about $110 each.

Eesh.

[TheOldMan]

It's exactly like the standard Turbografx style case

I see. I assume you modeled the door as well, then. I have found that different 'stock' cd cases have slightly different positions for various things, like the half-moon booklet holders...and of course the door pins <sigh>. That's partly why we went with a 3 piece case.

The only problem with using Shapeways....

Yes, I know. That's why we don't have the trays available for sale
FWIW, We can print them for about $5 in materials; they just take a hellava long time, and the corners tend to warp if you don't watch them closely at the start of printing. I'm hoping to get a bigger bed printer for XMas, and do a rails replacement so it can print faster....
Maybe 2015 will be the year we can replicate everything turbo

(Got a design for the controller housing? That's next on my list. I've seen schematics for the electronics/board, and would probably use actual switches rather than those rubber pads.)

[SuperPlay]

nice piece of work there jelloslug :-)

[jelloslug]

It's exactly like the standard Turbografx style case

I see. I assume you modeled the door as well, then. I have found that different 'stock' cd cases have slightly different positions for various things, like the half-moon booklet holders...and of course the door pins <sigh>. That's partly why we went with a 3 piece case.

The only problem with using Shapeways....

Yes, I know. That's why we don't have the trays available for sale
FWIW, We can print them for about $5 in materials; they just take a hellava long time, and the corners tend to warp if you don't watch them closely at the start of printing. I'm hoping to get a bigger bed printer for XMas, and do a rails replacement so it can print faster....
Maybe 2015 will be the year we can replicate everything turbo

(Got a design for the controller housing? That's next on my list. I've seen schematics for the electronics/board, and would probably use actual switches rather than those rubber pads.)

I did not do the lid.  I can make a model of it but new older (thicker) jewel cases are still readily available for not much money.  I have not modeled the controller case but I can.  Be aware that there are two different controller cases (and boards) though.

[esteban]

If you look at most TG-16 CD-rom setups that have the case the one thing that sticks out is that most of them are missing one or both of the latches.  It's not a terribly complex part so I modeled it and had a pair made.  I still need to dye them but they function just fine.





I can have a batch of them made to sell if there is any interest.

I ABSOLUTELY NEED TWO (a set)!

I was so careful, but the damn things broke on me back in the 90's. Anyone with half a brain could have told NEC that the design was too flimsy to be practical, especially for a "rugged" case designed to transport and hold super-expensive gear.

[jelloslug]

Well it looks like there is enough interest for me to have some made.  It looks like it will take around two weeks to get them.

[Black Tiger]

I don't currently own a Turbo-CD case, but would love to buy a pair or two.

[blueraven]

I still need 4-6 I have 2 broken cases.

[jelloslug]

Here is the clip after I dye it.  The font for "PUSH" is a little thin but overall it's not bad it all and it works just fine.  The new clip is on the left and an original one is on the right.

[Lost Monkey]

Put me down for a pair..

[jelloslug]

I have ordered enough latches for 12 pairs as an initial run.  They will be $20 shipped for the pair (paypal gift preferred) to the US and whatever the shipping difference is for out of the US.  I will contact everyone in order in this thread in order of posting with a PM. After that I will see how many more (if any) and get another run started.  The first ones took about two weeks to get but they could take up to four weeks according to Shapeways.

[jelloslug]

I have PMed everyone that said they were interested.  If I missed you or you want a pair just post here.

[HailingTheThings]

Here is the clip after I dye it.  The font for "PUSH" is a little thin but overall it's not bad it all and it works just fine.  The new clip is on the left and an original one is on the right.

Damn, those look super nice, if I had a case, I'd totally.

[jelloslug]

Will you be doing another run at some point? I want... but 1) don't have a case yet and 2) am too broke due to too many childrens until I win the lotto.

I can have them made at anytime.  Ordering just 2 of them will be a bit more though as the shipping from Shapeways won't be spread out over a big batch.