Turbo CD-Rom2 unit making strange noise

[turbokon]

Here is a new one on me.  I have this cd-rom2 unit that is making strange noise, which sounds like dial-up, during loading.  It has new gears and a few caps replaced.  CD games seems to work fine other then the noise between loads. Any ideas?

[Keith Courage]

It's a resister in the middle of the motherboard. Check on the underside of the screw that holds the board down. Sometimes this resister can get smashed/cracked during shipment.  I've encountered this 4 times now myself.

Usually it's the one I circled in this pic.  http://postimg.org/image/wcbf11dqz/

[Bernie]

Is this the one you got from me?

[turbokon]

Is this the one you got from me?

Yessir it is:)

Keithcourage, you hit the nail right on the head.  Resistor 168 was damaged.  It was a 10k ohm resister.  Replaced it and it fixed the problem.

[Ninja16608]

I said it before and I'll say it again KC you are the man, just by listening to it you knew what the problem was ahhahaha love this place!!!!!!!!!!!!!!!!!!!!! Glad to hear ya got it taken care of Turbokon.

[NightWolve]

Huh, interesting, the resistor is the most reliable electrical component too, it's the last thing that'd you look for in troubleshooting. That it's in a bad spot or something and physically gets smashed/banged makes sense as to why you're seeing early failure. Good to know about then, so 10 KOhms at location R168. Yeah, this is the first troubleshooting thread I've ever seen here pointing to a resistor, as far as I can remember at least.

[turbokon]

Huh, interesting, the resistor is the most reliable electrical component too, it's the last thing that'd you look for in troubleshooting. That it's in a bad spot or something and physically gets smashed/banged makes sense as to why you're seeing early failure. Good to know about then, so 10 KOhms at location R168. Yeah, this is the first troubleshooting thread I've ever seen here pointing to a resistor, as far as I can remember at least.

Actually this is the second unit I worked on that was caused by a bad or missing resistor.  I worked on a duo a couple of years ago with memory save issues.  Come to found out its memory save chip had an open circuit due to a missing resistor.

[Ninja16608]

Huh, interesting, the resistor is the most reliable electrical component too, it's the last thing that'd you look for in troubleshooting. That it's in a bad spot or something and physically gets smashed/banged makes sense as to why you're seeing early failure. Good to know about then, so 10 KOhms at location R168. Yeah, this is the first troubleshooting thread I've ever seen here pointing to a resistor, as far as I can remember at least.

Yeah It is very rare to hear about a resistor in any device lol. I guess when the screw crushes it, it takes a toll. Seems to me like NEC didn't think that one through or no one caught it.

[turbokon]

Come to think of it, my LT that I just recapped had cap leakages affecting a couple of resistors.  I couldn't get any power to the LCD after recapping.  After removing those resistors and cleaning underneath them, LCD fired right up.

I've also came across a few GT/TE where the small smd resistors (I think sizes 0405) by hu6280 that got damaged by whomever tried to recapped them before me.  These resistors affected the on board controller function. 

[Marll]

I've had this issue (though not as horrible sounding as that vid) since day 1 with my CD when I got it in 91. I thought this was just the way they sounded.

Had a buddy buy another CD off of craigslist a couple years ago and it was silent, it was WEIRD to hear that...almost wrong 

I think that I'll probably fix it though since it's not supposed to be like that when I start doing a few more mods to my system.

[Marll]

So, those that have repaired this issue before, is there any reason that you specifically need to use a surface mount resistor? I was planning on doing this soon, but could only find some really small 10k ohm through hole type resistors. any reason the leads couldn't be cut short, laid flat and soldered to the pads?

[turbokon]

So, those that have repaired this issue before, is there any reason that you specifically need to use a surface mount resistor? I was planning on doing this soon, but could only find some really small 10k ohm through hole type resistors. any reason the leads couldn't be cut short, laid flat and soldered to the pads?

It will be ok to use the leaded resistor as long as you have enough room to solder the leads to the pads.

[Marll]

Cool thanks, I figured that was the case, now just need to open up the unit to see if that's the case.

If not, where is it that most of you guys are ordering your parts for these types of repairs?

[Keith Courage]

Most of time with surface mount resisters I end up taken them off of other older CD drives or other dead video game systems instead of ordering new. Sorry, that doesn't help you out with where to order from.

[crans]

i use mouser or digikey but price is not great if you just need one of something.